Polytrol is a deep penetrating oil which restores the original colour and appearance of dull or tarnished plastics, gelcoats, metals, and other surfaces.
It penetrates the surface, re-wetting the pigments to restore their lustre and colour which has been lost through exposure to sunlight, rain, and pollution and it also gives corrosion protection. When used on tarnished metals, it brings back the shine and gives long-term protection against corrosion.
Simple to apply using a cloth or soft brush, it’s ready to wipe off in just 10 minutes! It can be used on both horizontal and vertical surfaces and can even be used on fibreglass (GRP). Polytrol dries to a tough and long-lasting flexible finish which does not leave a film – so it won’t peel or flake.
Polytrol is now available in a handy 250ml spray can, great for quick application and difficult to reach areas. Please see the directions for use to find out how to apply it.
Ideal Uses for Polytrol Colour Restorer
- Brightening faded car bumpers
- Reviving the gelcoat on your boat
- Restoring the shine to metal fixtures
- Rejuvenating flat or chalky paint dulled by weathering
- Brightening the surface of tiles in stone, terracotta, marble, slate, etc.
- Reviving the colour of faded garage doors
Restrictions
DO NOT use Polytrol on white surfaces, it will not work as Polytrol is designed to restore pigments.
Surface Preparation
All surfaces must be clean, dry and free of dirt, grease, grime and mildew. All waxes, polishes, silicone etc. should be completely and thoroughly removed. Treat any mildew with a 50:50 bleach and water solution. Scrub the solution on to the surface and allow it to stand for 10-15 minutes then rinse thoroughly.
Using Polytrol on plastic, gelcoat, tiles, painted surfaces etc.
Clean the surface with warm soapy water or Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.
Using Polytrol on stone, brick, etc.
Clean the surface with Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.
Using Polytrol on metal
Clean the surface with warm soapy water and rinse thoroughly or use an appropriate solvent (follow manufacturer’s instructions). Leave the surface to dry for a minimum of 24 hours.
Application of Polytrol Colour Restorer
General directions
Always work in areas that can be completed 10-20 minutes to ensure an even appearance. If the surface absorbs the Polytrol unevenly (i.e. some matt and some shiny patches) move any surplus oil from shiny areas to matt areas. Wipe off any excess Polytrol with a lint-free cloth before it becomes tacky. For a shinier finish, buff the surface with a lint-free polishing cloth.
When using the Polytrol 250ml spray can, simply spray on liberally, wipe off any excess and leave to dry.
Applying Polytrol to plastic, gelcoat, tiles, painted surfaces etc.
Apply Polytrol liberally and evenly with a brush or cloth. Allow it to work for 10-20 minutes. Wipe off any excess with a clean lint-free cloth. Leave it to dry.
Applying Polytrol to stone, brick, etc.
Apply Polytrol liberally and evenly with a brush or cloth and leave it to work for 10-20 minutes. Brush out or wipe off any excess Polytrol with a clean lint-free cloth. Leave it to dry.
Applying Polytrol to metal
Apply Polytrol using a fine wire wool (000 grade) soaked in Polytrol and allow it to work for 10-20 minutes. Wipe off any excess Polytrol with a clean lint-free cloth. Leave to dry.
Note: Polytrol is not a surface coating. Its place is in the surface, not on top.
Maintenance
Maintenance is due when a Polytrol treated surfaces shows signs of fading. Prepare and re-treat surfaces as directed above.
Clean Up
Clean any tools used with white spirit. Polytrol is non-flammable, however any rags, steel wool etc. soaked in Polytrol may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water-filled metal container, before disposing of them with household waste. Rags may be laid flat and air-dried before discarding.
Things to Remember
- Cover and protect everything you do not wish to treat.
- Apply between +5°C and +35°C.
- Do not apply in direct sunlight or on to hot surfaces.
- Do not allow excess Polytrol to dry and create a film on the surface (always remove excess product).
- Do not use Polytrol on white surfaces.
Martin Hill –
Frankly I’m astounded! I misguidedly attempted to clean paint off the frames with thinners…
I think the attached photos speak for themselves, thank you for an amazing product!
Patti –
Verified Owner
Received my Polytrol on time.My black composite front door was extremely bleached as is situated south facing and in full sun. Had differing opinions about repainting but decided on trying Polytrol. Followed instructions and only took 20 minutes as easy to apply. I am delighted with the result as the door looks brand new and all blemishes and faded areas were easily covered and only used quarter of my half litre tin. Would certainly recommend. One of the best products on the market.
John Mountford –
Polytrol, is an absolutely fantastic product. My garage door was getting quite faded so I purchased a tub 1ltr (way too much for one garage door). It was so easy to use, just apply with a cloth (just like cleaning the door with a damp cloth). It was so easy that I didn’t have a lot of confidence that it would work, but after drying, it looked absolutely great. I have just, two years later, redone the garage door and again had a fantastic result. I can’t praise it enough (I am so used to products not living up to expectations and this was a very pleasant exception).
Liz Wakeman –
Verified Owner
Absolutely unbelievable result. Was sceptical at first but we are truly blown away by the results. So quick and easy to use as well. Job done in less than hour (double Garage composite doors) with amazing results. Highly recommend.
Charlotte –
Verified Owner
This product is amazing! I used it on my black composite stable door as it had started to fade & it looks like new. My other half was so impressed he used it on the black plastic parts of his car bumpers as well. I really wish I’d taken before & after photos so I could show just how good it is & what a difference it makes.
Peter liddle –
Used the polytrol on a 12 years old black composite and I’m delighted with the out come the doors as good as new , would most defiantly recommend this product.
Steve Colwill –
Verified Owner
My green fibreglass observatory was looking very faded and dull after four years of exposure to the elements. The manufacturers recommended Polytrol to restore it to its former glory, so I ordered a one-litre can. I treated the whole structure with just half the can and have to say I am delighted with the results. It now looks like new again, with no trace of tarnishing and the colour has been restored to a deep lustre. 👍🏻
Brian –
Just chanced upon your advert while browsing the net looking for a product that would improve the look of my door, and I am so very glad that I did – couldn’t have wished for a better result!
Jo –
Bought the colour restorer for my composite door which had faded badly over time. Product was easy to use and took about 10mins for me to coat. So pleased with the way it has restored the colour. It now looks like a brand new door.
Anthony Pullen –
Bought this to revive the bumpers on my vw transporter, I have used lots of products that say they bring them back as new but none of them lasted for more than a month !
I was so impressed with the results I used it on a composite door in my street and the owner
was so happy they wanted to pay me ! what a bonus that payment paid for the 1ltr tin that I had bought, And I still have 3/4 of the product , will be on the lookout for more front doors and who knows it might be a nice little earner.