Polytrol is a deep penetrating oil which restores the original colour and appearance of dull or tarnished plastics, gelcoats, metals, and other surfaces.
It penetrates the surface, re-wetting the pigments to restore their lustre and colour which has been lost through exposure to sunlight, rain, and pollution and it also gives corrosion protection. Â When used on tarnished metals, it brings back the shine and gives long-term protection against corrosion.
Simple to apply using a cloth or soft brush, it’s ready to wipe off in just 10 minutes! It can be used on both horizontal and vertical surfaces and can even be used on fibreglass (GRP). Polytrol dries to a tough and long-lasting flexible finish which does not leave a film – so it won’t peel or flake.
Polytrol is now available in a handy 250ml spray can, great for quick application and difficult to reach areas. Please see the directions for use to find out how to apply it.
Ideal Uses for Polytrol Colour Restorer
- Brightening faded car bumpers
- Reviving the gelcoat on your boat
- Restoring the shine to metal fixtures
- Rejuvenating flat or chalky paint dulled by weathering
- Brightening the surface of tiles in stone, terracotta, marble, slate, etc.
- Reviving the colour of faded garage doors
Restrictions
DO NOT use Polytrol on white surfaces, it will not work as Polytrol is designed to restore pigments.
Surface Preparation
All surfaces must be clean, dry and free of dirt, grease, grime and mildew. All waxes, polishes, silicone etc. should be completely and thoroughly removed. Treat any mildew with a 50:50 bleach and water solution. Scrub the solution on to the surface and allow it to stand for 10-15 minutes then rinse thoroughly.
Using Polytrol on plastic, gelcoat, tiles, painted surfaces etc.
Clean the surface with warm soapy water or Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.
Using Polytrol on stone, brick, etc.
Clean the surface with Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.
Using Polytrol on metal
Clean the surface with warm soapy water and rinse thoroughly or use an appropriate solvent (follow manufacturer’s instructions). Leave the surface to dry for a minimum of 24 hours.
Application of Polytrol Colour Restorer
General directions
Always work in areas that can be completed 10-20 minutes to ensure an even appearance. If the surface absorbs the Polytrol unevenly (i.e. some matt and some shiny patches) move any surplus oil from shiny areas to matt areas. Wipe off any excess Polytrol with a lint-free cloth before it becomes tacky. For a shinier finish, buff the surface with a lint-free polishing cloth.
When using the Polytrol 250ml spray can, simply spray on liberally, wipe off any excess and leave to dry.
Applying Polytrol to plastic, gelcoat, tiles, painted surfaces etc.
Apply Polytrol liberally and evenly with a brush or cloth. Allow it to work for 10-20 minutes. Wipe off any excess with a clean lint-free cloth. Leave it to dry.
Applying Polytrol to stone, brick, etc.
Apply Polytrol liberally and evenly with a brush or cloth and leave it to work for 10-20 minutes. Brush out or wipe off any excess Polytrol with a clean lint-free cloth. Leave it to dry.
Applying Polytrol to metal
Apply Polytrol using a fine wire wool (000 grade) soaked in Polytrol and allow it to work for 10-20 minutes. Wipe off any excess Polytrol with a clean lint-free cloth. Leave to dry.
Note: Polytrol is not a surface coating. Its place is in the surface, not on top.
Maintenance
Maintenance is due when a Polytrol treated surfaces shows signs of fading. Prepare and re-treat surfaces as directed above.
Clean Up
Clean any tools used with white spirit. Polytrol is non-flammable, however any rags, steel wool etc. soaked in Polytrol may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water-filled metal container, before disposing of them with household waste. Rags may be laid flat and air-dried before discarding.
Things to Remember
- Cover and protect everything you do not wish to treat.
- Apply between +5°C and +35°C.
- Do not apply in direct sunlight or on to hot surfaces.
- Do not allow excess Polytrol to dry and create a film on the surface (always remove excess product).
- Do not use Polytrol on white surfaces.
Nick Cooper –
Verified Owner
I didn’t think the product would actually work on my composite door, I was wrong, the door is as good as new as giving it one coat in the evening then rubbing it down with a suitable cloth the next morning, excellent product delivered on time
Owatrol Team –
Hi there Nick,
Fantastic to hear! Thank you so much for sending us in some pictures too – we love to see the before and after.
All the best,
The Owatrol Team
Steve Bowler –
Verified Owner
Great product and very easy to apply to give an amazing difference.
Biddy Small –
Verified Owner
Faded door to shiny door, very good. Was a bit unsure how much to wipe off as the instructions were a bit unclear, but looked good when done.
Colin Barnes –
Verified Owner
Good product delivered at the speed of light!
Reg Ruckledge –
Verified Owner
Revived kitchen worktops, very pleased with the result. Applied the polytrol with a 1&1/2 inch fine bristled brush for a better finish after first trying with a lint free cloth.
Tony Proctor –
Verified Owner
Used it on my very faded black composite door, wow what a difference. My first time using this and 10 out of 10 from me.
Alun R –
Verified Owner
Great product. Used it on a faded grey composite door and it came up like new again.
Also used it on a kitchen touch bin top that had lost some of its colour. Worked perfectly.
Andy Herbert –
Verified Owner
Great stuff, very versatile, makes things look like new.
Michael Ellis –
Verified Owner
For once, a product that exceeded our expectations. We purchased a small tin for a dark coloured UPVC door which had faded in places and applied the Owatrol in accordance with the instructions. The difference between before and after is truly remarkable and we are impressed and delighted with the result.
Alastair –
Verified Owner
Very pleased with the outcome, our front door looks as new with so little effort. I was surprised by how little of the liquid was used as at first glance I thought the tin was far too small to cover my door, how wrong I was as I have enough left to restore another three doors if needed. the only negative comment is that the tin doesn’t seal very well after use.