Polytrol & Pura-Trol

Application tools for Pura-Trol

• Pump Sprayer
• Brush
• Sponge
• Hose
• Power Washer

Surface Preparation for Pura-Trol

First, remove any organic surface growth – moss for example.

Dirty Surfaces: 1 part Pura-Trol to 20 parts water.
Very Dirty Surfaces: 1 part Pura-Trol to 10 parts water (for use on wheels for example).

Pura-Trol is a concentrated formula. Use only the recommended dilutions. Do not use undiluted

Application of Pura-Trol

• Make up a diluted solution as dictated by the surface contamination.
• Stir or shake the solution well to ensure Pura-Trol is well mixed in.
• Apply diluted Pura-Trol to the surface using a brush, sponge or pump sprayer.
• Allow the solution to work for 10 minutes.
• Do not allow the solution to dry on the surface while working.
• Rinse the surface with fresh clean water using a hose, power washer or bucket and sponge (making sure you change
  water regularly).

Things to remember

• Cover everything you do not wish to clean.
• Apply between 10°C and 25°C.
• Do not apply in direct sunlight or to hot surfaces.
• When applying by spray, adjust the nozzle to prevent the formation of a mist.

Surface Preparation for Polytrol

All surfaces must be clean, dry and free of dirt, grease, grime and mildew. All waxes, polishes, silicone etc. should be completely and thoroughly removed. Treat any mildew with a 50:50 bleach and water solution. Scrub the solution on to the surface and allow it to stand for 10-15 minutes then rinse thoroughly.

Using Polytrol on plastic, gelcoat, tiles, painted surfaces etc.

Clean the surface with warm soapy water, Pura-Trol or Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.

Using Polytrol on stone, brick, etc.

Clean the surface with Pura-Trol or Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.

Using Polytrol on metal

Clean the surface with warm soapy water and rinse thoroughly or use an appropriate solvent (follow manufacturer’s instructions). Leave the surface to dry for a minimum of 24 hours.

Application of Polytrol Colour Restorer

General directions

Always work in areas that can be completed 10-20 minutes to ensure an even appearance. If the surface absorbs the Polytrol unevenly (i.e. some matt and some shiny patches) move any surplus oil from shiny areas to matt areas. Always wipe away excess Polytrol with a lint-free cloth before it becomes tacky. For a shinier finish, buff the surface with a lint-free polishing cloth.

When using the Polytrol 250ml spray can, simply spray on liberally, wipe off the excess and leave to dry.

Applying Polytrol to plastic, gelcoat, tiles, painted surfaces etc.

Apply Polytrol liberally and evenly with a brush or cloth. Allow it to work for 10-20 minutes. Wipe off the excess with a clean lint-free cloth. Leave it to dry.

Applying Polytrol to stone, brick, etc.

Apply Polytrol liberally and evenly with a brush or cloth and leave it to work for 10-20 minutes. Brush out or wipe off the excess Polytrol with a clean lint-free cloth. Leave it to dry.

Applying Polytrol to metal

Apply Polytrol using a fine wire wool (000 grade) soaked in Polytrol and allow it to work for 10-20 minutes. Wipe off the excess Polytrol with a clean lint-free cloth. Leave to dry.

Note: Excess Polytrol must be wiped away. It is not a surface coating and as such, its place is in the surface, not on top.

Maintenance

Maintenance is due when a Polytrol treated surfaces shows signs of fading. Prepare and re-treat surfaces as directed above.

Clean Up

Clean any tools used with white spirit. Polytrol is non-flammable, however any rags, steel wool etc. soaked in Polytrol may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water-filled metal container, before disposing of them with household waste. Rags may be laid flat and air-dried before discarding.

Things to Remember

• Cover and protect everything you do not wish to treat.
• Apply between +5°C and +35°C.
• Do not apply in direct sunlight or on to hot surfaces.
• Do not allow excess Polytrol to dry and create a film on the surface (always remove excess product).
• Do not use Polytrol on white surfaces.