Polytrol is a deep penetrating oil which restores the original colour and appearance of dull or tarnished plastics, gelcoats, metals, and other surfaces.
It penetrates the surface, re-wetting the pigments to restore their lustre and colour which has been lost through exposure to sunlight, rain, and pollution and it also gives corrosion protection. Â When used on tarnished metals, it brings back the shine and gives long-term protection against corrosion.
Simple to apply using a cloth or soft brush, it’s ready to wipe off in just 10 minutes! It can be used on both horizontal and vertical surfaces and can even be used on fibreglass (GRP). Polytrol dries to a tough and long-lasting flexible finish which does not leave a film – so it won’t peel or flake.
Polytrol is now available in a handy 250ml spray can, great for quick application and difficult to reach areas. Please see the directions for use to find out how to apply it.
Ideal Uses for Polytrol Colour Restorer
- Brightening faded car bumpers
- Reviving the gelcoat on your boat
- Restoring the shine to metal fixtures
- Rejuvenating flat or chalky paint dulled by weathering
- Brightening the surface of tiles in stone, terracotta, marble, slate, etc.
- Reviving the colour of faded garage doors
Restrictions
DO NOT use Polytrol on white surfaces, it will not work as Polytrol is designed to restore pigments.
Surface Preparation
All surfaces must be clean, dry and free of dirt, grease, grime and mildew. All waxes, polishes, silicone etc. should be completely and thoroughly removed. Treat any mildew with a 50:50 bleach and water solution. Scrub the solution on to the surface and allow it to stand for 10-15 minutes then rinse thoroughly.
Using Polytrol on plastic, gelcoat, tiles, painted surfaces etc.
Clean the surface with warm soapy water or Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.
Using Polytrol on stone, brick, etc.
Clean the surface with Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.
Using Polytrol on metal
Clean the surface with warm soapy water and rinse thoroughly or use an appropriate solvent (follow manufacturer’s instructions). Leave the surface to dry for a minimum of 24 hours.
Application of Polytrol Colour Restorer
General directions
Always work in areas that can be completed 10-20 minutes to ensure an even appearance. If the surface absorbs the Polytrol unevenly (i.e. some matt and some shiny patches) move any surplus oil from shiny areas to matt areas. Wipe off any excess Polytrol with a lint-free cloth before it becomes tacky. For a shinier finish, buff the surface with a lint-free polishing cloth.
When using the Polytrol 250ml spray can, simply spray on liberally, wipe off any excess and leave to dry.
Applying Polytrol to plastic, gelcoat, tiles, painted surfaces etc.
Apply Polytrol liberally and evenly with a brush or cloth. Allow it to work for 10-20 minutes. Wipe off any excess with a clean lint-free cloth. Leave it to dry.
Applying Polytrol to stone, brick, etc.
Apply Polytrol liberally and evenly with a brush or cloth and leave it to work for 10-20 minutes. Brush out or wipe off any excess Polytrol with a clean lint-free cloth. Leave it to dry.
Applying Polytrol to metal
Apply Polytrol using a fine wire wool (000 grade) soaked in Polytrol and allow it to work for 10-20 minutes. Wipe off any excess Polytrol with a clean lint-free cloth. Leave to dry.
Note: Polytrol is not a surface coating. Its place is in the surface, not on top.
Maintenance
Maintenance is due when a Polytrol treated surfaces shows signs of fading. Prepare and re-treat surfaces as directed above.
Clean Up
Clean any tools used with white spirit. Polytrol is non-flammable, however any rags, steel wool etc. soaked in Polytrol may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water-filled metal container, before disposing of them with household waste. Rags may be laid flat and air-dried before discarding.
Things to Remember
- Cover and protect everything you do not wish to treat.
- Apply between +5°C and +35°C.
- Do not apply in direct sunlight or on to hot surfaces.
- Do not allow excess Polytrol to dry and create a film on the surface (always remove excess product).
- Do not use Polytrol on white surfaces.
Ladyfromchester –
Verified Owner
Used Polytrol on my cast aluminium garden furniture which had faded to grey after 10 years in the sun.
I am pleased to say the furniture is back to its lovely bronze finish. It has absorbed the oil over a week or so, going from extremely shiny towards the original matte finish.
Very economical to use, 125ml did Bistro set and I used another 700ml approx on 6 chairs and large table.
Owatrol Team –
Hi there Lady,
Thank you for your kind review and feedback on Owatrol Polytrol – we’re very happy to hear how well it worked for you on your cast aluminium garden furniture.
It’s looking good as new and will hopefully last at least another 10 years! 🙂
All the best,
The Owatrol Team
Geoff Page –
Verified Owner
I’ve used Owatrol paint conditioner on a narrowboat and expected great things from the colour restorer. First off the tag holding the paint expanding spout broke off and needed pliers to pull up and subsequent sticking a hole into it in order to use the product. As for the product itself was easy to apply but looks as though it was painted. I thought the product would be absorbent. It all looked is OK but I’m not convinced yet. Let’s get some weather on it for a final judgment.
Sort out the pull out funnel would help.
Owatrol Team –
Hi there Geoff,
Thank you for taking the time to share your feedback of Polytrol.
It is most unfortunate that the pull up spout broke for you – after 9 years this is honestly my first time of hearing this happen, so apologies you had that experience.
We’re pleased to hear that you found Polytrol easy to apply. We were interested to read your comment regarding the “painted” appearance, as this is not typically the finish that Polytrol is designed to produce.
Unlike paints, varnishes or other surface coatings, Polytrol works by penetrating into the material to restore colour from within, rather than forming a film on the surface. When applied correctly, the finish should look natural rather than coated.
A ‘painted’ or surface-coated appearance can sometimes occur if there are contaminants, previous treatments, or residues on the substrate that prevent the product from being able to penetrate fully. It can also happen if any excess product is not wiped away after the recommended working time, as Polytrol should not be left to dry on the surface.
For best results, the surface should be thoroughly cleaned (as well as dried) and free from dirt, grease, oils, waxes, sealers and any previous coatings before application. After allowing the product to work for approximately 10–20 minutes (maximum), any and all excess should be removed using a clean, lint-free cloth.
If you would like to discuss your application in more detail, we’d be very happy to help and review the preparation and application process with you, to ensure you’re getting the best possible result from the product.
Please feel free to call us on: 01582 592707 or email us directly at: sales@owatroluk.com
Thank you again for your feedback.
All the best,
The Owatrol Team
Chris Roberts –
Verified Owner
I ordered a 125ml tin to refresh my red composite front door. Arrived the next day. Very easy to apply and makes the door look like new.
A product that does what it says. 🙂
Owatrol Team –
Hi there Chris,
Thank you very much for your kind review of Owatrol Polytrol – we’re happy to hear it worked well for you and your red composite front door 🙂
All the best,
The Owatrol Team
Ros Mills –
Verified Owner
The product was easy to use and the door looks good but I was disappointed that it did not restore the colour to the edges surrounding the glass which have faded.
Barbara Girdler –
Verified Owner
Well impressed with this product our sun faded black composite door looks brand new
Louise Farrance –
Bought this to restore a faded hot tub – I never bother to write reviews but I’m seriously blown away with how fantastic this product worked and it was so easy to apply. A little product goes a long way. The photo shows project half way through to show the difference.
Owatrol Team –
Hi there Louise,
Thank you for your kind review of Polytrol – we’re happy to hear, and see, how well it worked for you on your hot tub.
All the best,
The Owatrol Team
Tina Arul –
Verified Owner
I bought the polytrol to try to revive my front door. I saw someone using it on YouTube.
I wasn’t disappointed- the product went on easily with a clean cloth and dried quickly and since then people have commented positively. My front door looks great.
So good to buy something which is not a false claim and literally does what it says on the tin.
Will buy again.
Owatrol Team –
Hi there Tina,
Thank you for your kind review of Polytrol being used on your front door.
We’re very happy to hear that it worked well for you 🙂
All the best,
The Owatrol Team
Paul –
Verified Owner
Best product I have ever used
Solved the fading chrome trim issue on my Mercedes
Fantastic
Owatrol Team –
Hi there Paul,
Thank you for your kind review of Polytrol – we’re happy to hear how well it has worked on your Mercedes chrome work 🙂
All the best,
The Owatrol Team
Leslie Anne –
Verified Owner
This is an excellent product. Someone had mentioned our door was looking faded, so I checked on the internet for suitable products and found Owatrol Polytrol was recommended by many. It was easy to apply with a paint brush, it dried in just over 24 hours, and it made the door look new again. Sorry for the shadow and different angles in my photos, but you can get an idea of the improvement. Highly recommended!
Rodger childs –
Verified Owner
Brilliant.really smartened my car trim.